Tascam DA-98HR Manuel d'utilisateur télécharger pdf (Page 25)

100

4 – Menu operations–Assigning menus to function keys

TASCAM DA-98HR 25

2 This menu gives you two choices, Menu, and

Locate Position:

Menu uses the function keys as a quick way

of jumping around the menu system (4.3,

“Assigning menus to function keys”).

Locate Position assigns the ten

function keys to location memories (7.2,

“Function key location memories”)

3 Select the option with the § and ¶ keys.

NOTE

When you change the function of the “soft” keys between

menu and location functions, the values assigned to the

other function are not lost, and are restored when you next

change the function of the soft keys.

4.2.2 The SHIFT key and function keys

Usually, the 10 function keys and the LOC 2/PRE-

SET

and MEMO 2/ +/– keys perform the duties as

marked on the top of their labels (e.g. key G usually

works as the

CLEAR key).

To use the keys as function keys (whether location

keys, or as preset menu keys):

1 Press the

SHIFT key. The SHIFT indicator

starts to flash.

While it is flashing, these keys are used as

described on the bottom row of their labels

(e.g. key

H now becomes function key 3 (F3)).

2 Pressing a function key in menu mode will turn

off the flashing

SHIFT indicator, but the SHIFT

indicator continues to flash in location mode

after a function key has been pressed.

3 If the

SHIFT indicator is flashing, press the

SHIFT key again to stop the indicator flashing

and return the keys to their original functions

of their top printed labels.

4.3 Assigning menus to

function keys

It is quite likely that you will find yourself using a

few of the same menu functions many times (for

instance, manual adjustment of punch points) and

many of the menu functions only rarely (for instance,

whether the DA-98HRHR is a master or a slave unit).

The “

F” keys below the tape counter (F through O)

can be used as “soft keys”, providing quick access to

the menu screens you use most often.

4.3.1 To assign a menu screen to a key

1 Set the function key mode to Menu as

described in 4.2.1, “Function key modes”

2 Use the cursor and

ENTER keys to display the

menu function you want to assign to a key.

3 Press the

SHIFT key S (the indicator will

flash).

4 Press the

PRESET key R. The following will

appear on the display. The bottom line shows

the menu as selected in step 2.

5 Press the key (

F1 through F10) to which you

want to assign the menu screen.

This assigns the menu screen to the key and the

SHIFT indicator goes out.

4.3.2 Recalling an assigned menu

function

1 When the function key is set to Menu (4.2.1,

“Function key modes”), press the

SHIFT key S

(the indicator flashes).

2 Press the

F key (1 through 10) which has been

assigned to the menu function you want to

recall.

The menu screen is recalled, and the

SHIFT

indicator goes out.

4.4 Using the function keys as

number keys

Press the 10KEY key Q so that the indicator flashes.

While the indicator is flashing, the function keys are

used to enter the digit (

F1 enters a 1, F 2 enters a 2,

etc.) except for

F 10, which enters a 0. The MEMO 2

key

P is used to change the sign of numeric entries

where appropriate.

Function Key Mode

Select

Function Preset

PUSH FUNCTION KEY

Timecode Offset

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 99 100

Commentaires sur ces manuels

Pas de commentaire

Tascam DA-98HR Manuel d'utilisateur Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de cassettes Tascam DA-98HR